cbsite

Instruction of REFINE Plotter Driver 1INSTRUCTION of REFINE PLOTTER DRIVER 1. REFINE CUTTING PLOTTER DRIVER SET-UP (Windows 2000 for example) Please select: Start---Settings---Printers Instruction of REFINE Plotter Driver 2Please select Add printer. You should choose Next You should choose Local printer and then, select Next Instruction of REFINE Plotter Driver 3 You should choose the port which your cutting plotter are using, then, select Next. Select Have Disk Instruction of REFINE Plotter Driver 4Select Browse Find REFINEplotter.inf file, then, select Open Select OK Instruction of REFINE Plotter Driver 5 You should find: REFINE CUTTING PLOTTER, then, select Next NoteIf you have installed this plotter driver before, you should find following Reminding: 11 Please choose: Replace existing driver. Instruction of REFINE Plotter Driver 612 If you want to use this printer as the default printer, please choose Yes, then select next. NoteYou should not find this reminding if there is no other printer. 13 Select Do not share this printer, then, Select Next Instruction of REFINE Plotter Driver 714 Select No, then, Next 15 Select Finish. Please always select Still installing if there is any interface reminding you during installation. Instruction of REFINE Plotter Driver 816 You should find REFINE CUTTING PLOTTER at the end of installation. 2. PLOTTER SETUP You should make some setup on REFINE Cutting plotter before outputting. Instruction of REFINE Plotter Driver 9 You need to make some setting on General and Ports items. 2.1. General SetUp In General item, please click on Printing Preferences, you should find following interface at which we need to make some setting on Paper option and Compensation option. Instruction of REFINE Plotter Driver 10 Explanation for each item on this interface: 2.1.1. Paper option Set paper size, you can select the popular paper type from the listed options, or, you can select Custom, and set paper height and width at your request. Please set paper size according plotter cutting size and output medium size. It is better to set its value more than 10mm and less than 20000mm. We advice the optimum value should be set between 300mm and 3000mm. Instruction of REFINE Plotter Driver 11NoteYou should set the paper size according to your plotter cutting size as well as media size in order to avoid exceed cutting out of media scope. 2.1.2. Compensation options: Close compensation: After the machine finish one section of closed curves, it will send commands to blade and continue to revolve this closed curve to cut a bit of, thus guarantee the curve closed completely. The length unit for Closed Compensates is 1/10 mm, please do not set the value of CLOSE COMPENSATION too large which cause time waste in the cutting process. Angle compensation: Because of blade physical structure, the angle cannot cut very sharply thus effect the graph overall appearance, Angle compensation is set for better actual angle cut as sharp as it displays in Graph. Instruction of REFINE Plotter Driver 12See as below Sketch Map: x y a m n z (Re: how Angle Compensation works) From the above map, the curve will go by X, passes through Y arrives Z. By the setting of angle compensation, machine will go from X to M, via N, then arrive Z. Therefore, it makes the angle formed by XYZ to be sharper than original in order to compensate the imperfect on angle cut caused by blade itself. Herein, a is compensate length, is Compensate angle, ifis not more than the value set by you, the angle compensation will come into effect of the actual cutting. The length unit for Angle compensate is 1/10 mm, angle unit is degree, You can set this compensation value at actual demand, otherwise it will distort the graph and effect the overall cutting quality. Note Unit for both Close compensation and the length of Angle compensation is 0.1mm, Close compensation value: 3, length of Angle compensation: 2, compensation angle: 120, is recommended by us. Of course you can adjust these values according the actual situation to obtain best result. 2.2. PORT SetUp Instruction of REFINE Plotter Driver 13 Please choose LPT1: Printer port if the plotter connect to computer parallel port, otherwise you can choose COM for Serial port. Here for example of COM1, please select COM1:Serial Port then click on Configure port, Instruction of REFINE Plotter Driver 14 Please Set COM1 Properties as following: Instruction of REFINE Plotter Driver 153. ATTENTION 1. If you choose the paper type to be Custom, please set its size according your plotter cutting size, paper width and height. Our advice is set between 300mm and 3000mm 2. The unit of Close compensation and Angle Compensation length is 0.1mm, our advice is Close compensation:3, Angle compensation Length: 2, Angle: 120degree. Also you can adjust these values according its cutting in order to get satisfying result. 3. When you edit by any Design Software, please set its layout size to be the same as the paper size value set under Printing Preferences, so that you can adjust the graph layout on the media more conveniently. 4.Before printout, youd better Print preview the image layout on the paper in case of improper cutting work. You can adjust images position to make sure it to be at Top Left Corner on the page. 5. If you edit by some special Design software and can print out directly to the plotter even without our Print driver, you should not install this driver in your computer; If you have installed the driver already, please try to use parallel port (LPT) otherwise it will cause print failure. Then output the work from File menu File--Print. Instruction of REFINE Plotter Driver 164. Application 4.1 CorelDRAW Select FilePrint Setup Click on Properties. Instruction of REFINE Plotter Driver 17 NOTEThe values on above should be the same as your setup on foresaid item 2.1 Printing Preferences if you have made. But you also can adjust its value at your actual request. Instruction of REFINE Plotter Driver 18Select LayoutPage setup to enter below page setup interface. Please set the paper width and height herein to be the same with the values in Print properties to ensure the coherence between design and print. Please select FilePrint after edit in CorelDRAW. Instruction of REFINE Plotter Driver 19You can set up on output options on above, as well set or change Print Properties by click on Properties Then Print, then the machine will start to work. 4.2. Art-cut software Select PrintSetup to get into Print Setup interface as below. Instruction of REFINE Plotter Driver 20 Please select REFINE CUTTING PLOTTER from the listed device, then click on Properties. NOTESome software in Vector can not distinguish the paper size completely custom. Herein you can select some popular paper size for REFINE plotter at your demand.